![]() ![]() I’ve dug into the code a bit and it seems that the stm32L0x family is very constrained featurewise and it does not really support 6pwm in hardware and in software it is almost certain it will not work as too.īut the good news it that it will work for 3pwm and I’ll update the next library version for it.įor now, if you want to test the code you can replace the whole contents of your \src\drivers\hardware_specific\stm32_mcu. I already updated the IDE, the board definitions und the simpleFOC library to the newest versions. Si est activada, cambia la posicin del interruptor, y. When I try to compile it for the nucleo 64 in the arduino IDE, I get the following error messages: _Īrduino: 1.8.15 (Windows 10), Board: "Nucleo-64, Nucleo L053R8, Mass Storage, Enabled (generic 'Serial'), None, Low/Full Speed, Smallest (-Os default), Newlib Nano (default)"Ĭ:\Users\XXXXX\Documents\Arduino\libraries\Simple_FOC\src\drivers\hardware_specific\stm32_mcu.cpp: In function 'HardwareTimer* _initPinPWMLow(uint32_t, int)':Ĭ:\Users\XXXXX\Documents\Arduino\libraries\Simple_FOC\src\drivers\hardware_specific\stm32_mcu.cpp:73:15: error: 'struct TIM_OC_InitTypeDef' has no member named 'OCNPolarity' did you mean 'OCPolarity'?ħ3 | sConfigOC.OCNPolarity = TIM_OCNPOLARITY_HIGH Ĭ:\Users\XXXXX\Documents\Arduino\libraries\Simple_FOC\src\drivers\hardware_specific\stm32_mcu.cpp:73:29: error: 'TIM_OCNPOLARITY_HIGH' was not declared in this scope did you mean 'TIM_OCPOLARITY_HIGH'?Ĭ:\Users\XXXXX\Documents\Arduino\libraries\Simple_FOC\src\drivers\hardware_specific\stm32_mcu.cpp:75:15: error: 'struct TIM_OC_InitTypeDef' has no member named 'OCIdleState'ħ5 | sConfigOC.OCIdleState = TIM_OCIDLESTATE_SET įehler beim Kompilieren für das Board Nucleo-64. Insisto: Se supone que est desactivada de fbrica, pero si deseas verificarlo, ve a Configuracin, Actualizacin y Seguridad, Seguridad de Windows, Abrir Seguridad de Windows, Seguridad del Dispositivo, y finalmente Detalles de Aislamiento del Ncleo. The sketch is modified to work with a NEMA17 and an AS5600. Your device exceeds the requirements for enhanced hardware security.I am trying to exchange a arduino uno board with an nucleo 64, using the “angle control”-sketch. Once completed, Device security indicates: " Your device exceeds the requirements for enhanced hardware security." (Figure 6.)įigure 6.Memory access protection then should be - Present.Under Settings, Update & Security, Windows Security, Device Security, Core isolation, Core isolation details.Intel Whiskey Lake computers with Microsoft Windows 10 version 19H1 and beyond or for Intel Comet Lake computers with Windows 10 version 20H1 and beyond perform the following steps in the operating system. The Trusted Execution option must be enabled in the Virtualization Support, Trusted Execution settings. ![]() The VT for Direct I/O option must be selected in the Virtualization Support, VT for Direct I/O settings.The System Management Mode (SMM) SMM Security Mitigation option must be selected in the Security, SMM Security Mitigation settings.The Secure Boot - Secure Boot Enable setting must be ON and Microsoft UEFI CA option to OFF(Figure 1.).The following settings in the system BIOS must be configured to support Secured-Core personal computer. Gestin del hardware ( memoria, procesador, perifrico, forma de almacenamiento, etc. Gestin de los distintos programas informticos (tareas) de una mquina. ![]() Refer to What is BIOS and How to Update the BIOS on Your Dell System Generalidades En informtica, los sistemas operativos son el ncleo del ordenador que se asegura de: La comunicacin entre los programas que solicitan recursos y el hardware. ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |